Measuring the cartridge showed its length had remained unchanged.Powder coating provides a hard surface on bullets. They wiped out with a few brush strokes followed by two patches. Wearing latex gloves and picking out bullets is slightly faster, but touching the bullets in any way removes some powder. Harbor Freight buys their top quality tools from the same factories that supply our competitors. Recoil was sharp. Fired with 12.0 grains of Unique, the velocity and size of five-shot groups was pretty much the same whether the bullets were lubed and sized or powder coated and sized. The gun blows negatively charged powder onto positively charged bullets. After firing 20-some coated bullets through the .45, its bore was only slightly fouled, probably with primer residue.Often when shooting plain cast bullets, you get a face full of smoke and a taste of lead when the wind blows in your face. Because they look so cool, I’ll even keep on hand some .30-30 and .45 Auto ammunition loaded with powder-coated bullets.These bullets were cast from an NOE 453-210-RF mould. Coat cars, trucks and airplane parts with even cover and easy clean up. I wore a dust mask and latex gloves while handling the powder. 11FS powder. A perfect powder coating gun for vehicles at home or the shopThis easy-to-use powder coating gun provides a finish that is tougher than conventional paint. Powder-coating material is essentially plastic that has been ground into a fine powder, with resins, color and other ingredients added to provide the desired coating film. We cut out the middleman and pass the savings to you! Heat is applied to melt the powder that cools as a hard film, enclosing the bullets.Powder can be applied to bullets by several methods, from complicated to quick.

Just fill the tool with any standard powder coating paint and you’re ready to go. Pressure is what distorts a cast bullet and ruins accuracy. A Lyman borescope showed a smear of red at the beginning of the rifling and a few streaks in the bore. After 15 minutes the powder had melted and a shiny coat of paint appeared on the bullets, but some of the bullets looked weird – as in they had started to melt and flatten. 16 Oz. Others tumble bullets while wearing wool socks and dragging their feet across carpet.Bullets must be clean for the powder to stick. Some folks use tweezers to pick up each bullet and set it in a pan, which is time consuming.
I shot 20-some of these bullets through a .30-30 at a velocity of 1,267 fps. Nothing is freer of contaminates than freshly cast bullets, or bullets stored in a sealed container.Some advice I read suggested to shaking a container with powder and bullets like a paint-shaking machine.
The paint also increased the diameter of the bullet’s nose, making a tight fit in the chambers.Coated bullets contain no gooey lubricant that eventually gums up a seating die.This five-shot group was fired at 25 yards using a Colt Gold Cup National Match .45 ACP with bullets cast from an NOE 453-210-RF mould and loaded with Titegroup powder.Two coats of Harbor Freight red powder put a .003-inch-thick coat on the forward section of RCBS 7mm-145-SIL bullets, making the bullets too wide to fit in new 7mm-08 rifles.Pet Loads and Handloader are registered trademarks of Wolfe Publishing Company.Wolfe Publishing Company | 2180 Gulfstream Suite A | Prescott, AZ 86301 I gently rolled the bullets into a strainer positioned over a pail and lightly jiggled the strainer to drain excess powder.

Standing up a bunch of slender rifle bullets requires nimble fingers.Simply tumbling bullets and powder together in a container turned out the cheapest and easiest way to coat bullets evenly. I was really impressed.

The polyethylene surface of Ziploc bags and soft plastic tubs tends into attract electrons when brought into contact with other materials. All that vigorous shaking did for me was knock the powder off bullets. Bullets that were laying on their side came out of the oven with an even coat. It's just that simple!For any difficulty using this site with a screen reader or because of a disability, please contact us at Note: Specifications are approximate and subject to changeWe guarantee this product to be free from defects in materials and workmanship 90 days from the date of purchase. A toaster oven was purchased for $20 at a local store, with a coupon and a discount. Add to Cart Add to My List. To put that worry to rest, I applied two coats of Harbor Freight Red Powder to bullets cast from an LBT 358-200-FN mould and crimped the bullets in .357 Magnum cases over 14.0 grains of Accurate No. Just fill the tool with any standard powder coating paint and you’re ready to go.

An air compressor that provides 10 to 30 psi of air pressure is also required.